WilliamLam.com

Enable Auto Startup After Power Failure For Apple Mac Mini

by // 39 Comments

I recently came across a very useful tidbit after receiving several inquires asking how to configure an Apple Mac Mini to automatically startup after a power failure. This is extremely useful for situations where power is eventually restored and you are not physically around to press the power button. Automatically starting up after a power failure is not a new feature of the Mac Mini and it actually exists on most modern day systems and can be configured using a variety of tools.

The challenge arises when you are running ESXi, how do you go about enabling this functionality in ESXi itself? Well the answer is actually quite simple, you can enable this outside of ESXi. Normally to enable this feature you can either run a setpci command on UNIX/Linux system or configure the energy saver settings in OS X. Several folks from the VMTN community such as zippytiff and twuhabro have already confirmed having success using the latter option when booting OS X off a USB or SD card to modify the energy saving settings.

I finally got a chance to look into this a bit more for myself and with a bit of research, I found several other methods which also works and may potentially be easier.

Note: I have heard that historically the auto startup flag has not persisted in older Apple hardware, but for the new Mac Mini 5,3 and 6,2, they seem to be persisting without any issue from my testing. YMMV depending on your hardware and/or firmware.

Method 1 (Configure in OS X)

If you already have OS X install on your Mac Mini, then you just need open up the System Preferences and enable auto startup under the Energy Saver section. Once that has been enabled, you can then perform your ESXi installation.

If you already have ESXi installed, then you can use either Method 2 or 3.

Method 2 (Configure using bootable Ubuntu on USB)

We can create a bootable Ubuntu image running off of a USB device (minimal footprint) and run the following setpci command to enable auto startup:

setpci -s 0:1f.0 0xa4.b=0

If you are interested in the gory details on the above command, please refer to this great article which breaks it all down for you. After you have created your Ubuntu image using the instructions in the above link, you can boot off of the USB device (Make sure to hold down ALT/OPT key so you can select to boot off of the USB device). Once Ubuntu has booted up, you will right click on the purple icon on the upper left hand corner and type in terminal.

You will then launch the terminal application and type the following to change over to root user.

sudo su -

Finally, you will enter the above setpci command which will enable the auto startup. At this point, you can type reboot and remove the USB device.

Method 3 (Configure using bootable OS X on USB)

Another method is to create a bootable OS X image running off of a USB device and change the power management settings by using the pmset utility. To enable auto startup, run the following command in the terminal:

pmset autorestart 1

You will need the original OS X installer and if you are using either Lion or Mountain Lion, you can use Lion DiskMaker to help you create the bootable USB image (Make sure to hold down ALT/OPT key so you can select to boot off of the USB device). Once the OS X installer boots up, at the top select Utilities and click on the Terminal application.

Go ahead and run the above command to enable auto start and then type reboot and remove the USB device.

The last thing to do of course is to actually test this out on your Mac Mini. Go ahead and let the system boot up and then yank the power cord and then give it a few seconds before plugging it back in. You should see the Mac Mini automatically power back on after you plug the power back in.

References:

 

Configure Apple Mac Mini to Default Boot ESXi

by // 13 Comments

If you are running ESXi on an Apple Mac Mini and it is installed on a USB key, you probably have noticed that the Mac Mini tries to boot from disk by default and instead of using the USB device. This means when you reboot your ESXi host each time, you will need to hold down the "ALT/OPTION" key which will present you with a boot menu to select the device you wish to boot from.

This can be quite annoying if you have a headless setup for your Mac Mini and you just want it to automatically boot off of the right device containing your ESXi installation. To fix this, you can configure the default boot device which can be done by first selecting the device you wish to boot off of as shown in the screenshot above. Next, hold down on the "CONTROL" key which will turn the straight arrow into circular arrow icon as shown in the screenshot below.

Now you just need to either hit enter or if you have a mouse, click on the circular arrow icon and this will configure the default boot device the Apple Mac Mini will use going forward. It is that simple! If you want to boot off of another device after configuring the default boot device, you can still do so by holding down "ALT/OPTION" key while the Mac Mini is still booting up.

Credit goes to this site for solution. 

Installing ESXi 5.0 Update 2 on Mac Mini is Now a Breeze! (No Custom ISO/patches Needed!)

by // 15 Comments

VMware has just released ESXi 5.0 Update 2 which includes many bug fixes, but along with these fixes, these updates usually also include new inbox drivers as part of the default ISO image for ESXi. One important driver that I had noticed while going through the release notes is the inclusion of the tg3 (Broadcom) inbox driver:

  • Updates the tg3 driver to version 3.123b.v50.1
    The tg3 inbox driver version shipped with the ESXi 5.0 Update 2 is 3.123b.v50.1.

Disclaimer: The Apple Mac Mini is not officially supported by VMware. 

Why is this awesome!? Well, for those of you who own an Apple Mac Mini and would like to run ESXi, may recall an additional step is required to create a customized ESXi ISO to include an updated tg3 driver for the networking stack to function in an Apple Mac Mini. Though the steps have been documented here, it is great to see this working right out of the box using the new ESXi 5.0 Update 2 ISO from VMware. In addition to the networking stack functioning properly after installation, it also enables connectivity to an Apple Thunderbolt Ethernet adapter if you happen to have one connected to your Apple Mac Mini! You no longer have to create a custom ESXi ISO for the Thunderbolt Ethernet adapter as mentioned in an earlier article here.

Note: This article is only relevant to pre-2012 Apple Mac Mini, if you have a newer Apple Mac Mini 6,2 - Please refer to this article for installation.

Here are a few screenshots of running the latest ESXi 5.0 Update 2 on my Apple Mac Mini 5,3 as well as showing the Apple Thunderbolt Ethernet adapter active in ESXi:

If you want a tiny form factor for a vSphere home lab, you should definitely consider asking Santa for an Apple Mac Mini this Christmas 😉 Hope everyone has a Happy Holiday and Happy New Years!