WilliamLam.com

Virtually Speaking Podcast: MacOS Virtualization and MacStadium

by // Leave a Comment

Last week I had the pleasure to be on the Virtually Speaking Podcast (#1 Virtualization Podcast) to talk a little about the history and the use cases driving MacOS Virtualization in the Enterprise. In fact, this affects most if not every single organization that develops either an Apple MacOS and/or iOS application which includes VMware.

We also had a very special guest, Preston Lasebikan, a Systems Architect for MacStadium who gave us some insights into how they are supporting major Enterprise customers such as Dropbox, Capital One, Shopify, Box and many others using their Apple Mac Infrastructure which runs on VMware vSphere. If you never heard of MacStadium before, they are the largest service provider of Apple Mac Infrastructure as a Service in the world and there is a high probability your organization is already using them with you even knowing.

Click on the image below to listen 👇

Quick Tip - Suppress new core dump warning in ESXi 7.0

by // 5 Comments

You may have noticed new warning message after installing ESXi 7.0, this can happen if your ESXi installation is on a smaller local disk (Nested ESXi Appliance would also be affected) which does not have enough capacity for setting up a core dump target or if ESXi is booting from USB which also does not support core dumps by default.

No coredump target has been configured. Host core dumps cannot be saved.


It is certainly recommended that you have a core dump target configured, especially for Production systems. However, if you wish to suppress the warning, there is an ESXi Advance Setting which you can toggle called UserVars.SuppressCoredumpWarning (can be configure using Embedded ESXi Host Client or vSphere UI in vCenter Server) as well as ESXCLI. Below is the command to suppress the warning:

esxcli system settings advanced set -o /UserVars/SuppressCoredumpWarning -i 1

Changing the default size of the ESX-OSData volume in ESXi 7.0

by // 29 Comments

In ESXi 7.0, a new partition scheme was introduced which also brings along a new set of storage requirements. These changes are explained in the official documentation here and the following VMware KB 77009 also contains some additional info which can be helpful. Storage changes are not easy but this was necessary to not only better support some of the current capabilities but more importantly, it setups the foundation for future ESXi capabilities.

The biggest change to the partition layout is the consolidation of VMware Tools Locker, Core Dump and Scratch partitions into a new ESX-OSData volume (based on VMFS-L). This new volume can vary in size (up to 138GB) depending on a number of factors including the current ESXi boot media (USB SD-Card, Local Disk) but also the size of the device itself, which is explained in the official documentation.

From some of the comments on Twitter, Reddit and the direct inquiries that I have received, this new behavior seems to be most impactful to smaller homelabs where a fresh install of ESXi 7.0 has been performed. Folks have shared that their ESX-OSData volume has taken up 120GB which can be quite significant if you have a smaller disk which can be quite common. I normally install ESXi on a USB device and I also use vSAN, which has a different behavior and I have also not upgraded my physical ESXi host (E200-8D) to 7.0 yet.

I performed a fresh installation of ESXi 7.0 (running as Nested ESXi VM) that was configured with 1TB of storage and here is what the filesystem layout now looks:


We can see that the ESX-OSData volume takes up ~119.75GB, which is not too bad for 1TB volume but I can understand this may not be ideal if you have something smaller such as 250GB to 512GB disk. Due to the size of the local device, the boot options mentioned in the KB would not be helpful and I was curious myself if this ESX-OSData volume size could be configurable. In doing some research it looks like the size of the ESX-OSData can be specified using the following ESXi boot option (SHIFT+O during the initial boot) called autoPartitionOSDataSize

UPDATE (12/17/20) - Official support for specifying the size of ESX-OSData has been added to the release of ESXi 7.0 Update 1c with a new ESXi kernel boot option called systemMediaSize which takes one of four values:

  • min = 25GB
  • small = 55GB
  • default = 138GB (default behavior)
  • max = Consumes all available space

If you do not require or have 138GB for the ESX-OSData, you can override the default behavior by appending this option with the specified value (e.g. systemMediaSize=min). It is worth noting that by using this setting, the smallest ESX-OSData volume you can configure is 25GB. For homelabs or environment which require less than this, you would have to use the unsupported autoPartitionOSDataSize parameter , which is not officially supported as mentioned below.

Disclaimer: This may not be officially supported by VMware as it deviates from the system defaults and can have other unintended behaviors. Use at your own risk.

[Read more...]